Add to Chrome

Loudness Normalizer

Bring a song or podcast to a LUFS target and download it — measured and processed in your browser.

Audio tool

Normalize a track to a LUFS target

Runs in your browser

Drop a song or podcast here

or click to choose from your computer

MP3 · WAV · FLAC · AAC · M4A · OGG

✓ Local processing in your browser · Files are not uploaded to our servers

What is the Loudness Normalizer?

Loudness Normalizer sets a track to a target loudness measured in LUFS. Pick a target, check the result on the readouts, then listen to Original and Normalized one after the other. The gain is applied to the whole file in one step, so the sound stays the same and only the level changes.

Peak meters are not enough for this job. Two tracks can hit the same peak and still sound very different in volume, because loud, dense mixes feel louder than sparse ones. LUFS follows perceived loudness, so it is the number streaming platforms and broadcasters use.

Everything runs in your browser. The file is decoded, measured and rendered on your device, and the export is created locally, so there is no upload queue and no server step.

Good to know

  • Use -14 LUFS for music you publish to streaming services, -16 LUFS for podcasts and Apple Music, and -23 LUFS for broadcast.
  • Keep Prevent clipping on. It caps the gain so the peaks stay below -1 dBFS, which avoids distortion.
  • Choose WAV if you will edit the result again. MP3 is fine for sharing and playback.

How LUFS normalization works

01

Measure

The tool applies the BS.1770 K-weighting filter, which models how the ear responds to frequencies, and averages the loudness over 400 ms blocks. Quiet passages below the gate are ignored, as in EBU R128.

02

Compute the gain

The gain is the target minus the measured loudness. A track at -18 LUFS with a -14 target gets +4 dB. The gain is applied to every sample with the same factor.

03

Protect the peaks

If the gain would push the highest peak above -1 dBFS, the gain is reduced to that ceiling. The readout tells you when this happens, so you know the result is below the target.

Which target should you pick?

The target is the loudness you want the whole file to end up at. Pick the one closest to where the file will be played, then compare the Original and Normalized readouts before you export.

  • -14 LUFS for music and mixes you upload to streaming platforms. Louder sources are turned down, quieter ones are brought up to this level.
  • -16 LUFS for podcasts, spoken word and Apple Music style playback. Speech sits comfortably at this level and keeps more headroom.
  • -23 LUFS for broadcast and TV delivery under EBU R128. It is much quieter, so use it only when the destination asks for it.

If a clip is very quiet, a large gain can raise the noise floor too. Clean hiss first with the AI Noise Reducer, then normalize.

Frequently asked questions

What does LUFS mean?

LUFS (Loudness Units relative to Full Scale) is the measure of perceived loudness defined in ITU-R BS.1770. Unlike peak level, it follows how loud a track sounds to a listener, so two tracks at the same LUFS value sound about equally loud.

Which target should I choose?

-14 LUFS is the level most streaming services use as a reference. -16 LUFS is the Apple Music Sound Check level and a common choice for podcasts. -23 LUFS is the EBU R128 broadcast standard for TV and radio.

Will it make my track louder or quieter?

Either. A track quieter than the target gets a positive gain and becomes louder. A track louder than the target gets a negative gain and becomes quieter. The whole file gets one gain change, with no compression or limiting.

What does Prevent clipping do?

It stops the gain once the highest sample peak reaches -1 dBFS, so the result never distorts. Dynamic tracks can still hit the target exactly. Heavily compressed masters may end up below the target, which is the safe outcome. Turn it off only if you accept some clipping.

Does it lower the quality?

The gain is one multiplication on the decoded audio at the file's own sample rate. WAV is exported at 16 bit, so the only loss is rounding to 16 bit. MP3 adds the usual lossy encoding. Choose WAV if you plan to edit the file again.

Are my files uploaded anywhere?

No. Decoding, measuring and applying the gain all run on your device. Nothing is sent to Sound Booster servers. The MP3 encoder is loaded once from a public CDN, the first time you export an MP3.

Why does my mono file sound quieter in some players?

Some players send a mono file to both speakers, which makes it sound louder than the measurement. This tool measures the file as it is, using the BS.1770 weighting for a single channel.

Related tools

Check, boost or clean up the track after you normalize it.